GATOR SUPERSAND G2

• Residential and commercial use
• Traditional applications
• Concrete pavers, natural stone, wet cast products and clay pavers
• Streetscape, commercial work, steep slope, pool areas, patios, walkways, driveways and parking areas

• No dust, haze free, no blower, one watering
• For traditional applications, Rapid Set and rain safe 15 minutes after water activation
• Can be used for joints up to a maximum of 2″ (5 cm)
• ASTM C-144 gradation allows use in even the tightest joints
• OSHA silica crystalline compliant (OSHA 29 CFR 1926.1153)
• Works above 32°F (0°C)
• Faster installation time
• Waterproof bags: Lay bag flat on its back, so f ont of the bag is facing you. Intact pallets can be stored outdoors.
• 15 Year Limited Warranty

• Helps prevent weeds and damage caused by burrowing insects
• Helps prevent erosion due to wind, rain and freeze/thaw cycles

When maintaining the paver surface, apply Gator Shampoo to clean the entire paved surface including the paver joints. Wash, rinse and remove any residue by using a hose and a watering gun set to shower with the normal maximum water pressure from any residential or commercial building (typically 80 psi/550 kPa).

Moss

SUPERSAND G2 will not cause nor prevent moss, mold or mildew. Moss, mold and mildew are caused by certain on-site conditions including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product.

Clay Pavers

If used on clay pavers make sure they are 100% dry. Clay pavers tend to hold moisture, which can prematurely activate the SUPERSAND G2 while the sand is being spread over the paver surface, leaving a residue. Always apply on a test area before using the SUPERSAND G2 on clay pavers.

Per 50 lb (22.7 kg) bag (Paver 2-3/8” (6 cm) in height)	NARROW JOINTS 1/8” to 3/8” (3-9 mm)
Beige, Slate Grey	65-85 sq. ft. (7-7.9 sq.m.)

IMPORTANT INSTALLATION NOTES

Always refer to the latest SUPERSAND G2 Technical Data Sheet (TDS) at AllianceGator.com before installing SUPERSAND G2.

Pavers and slabs must be installed according to ICPI Tech Spec #2 traditional base (www.icpi.org) before SUPERSAND G2 installation.

Pavers’ sides and top surfaces must be completely dry. Do not apply if the paver surface is damp or wet. The damp or wet surface will cause SUPERSAND G2 to prematurely activate and will lead to the polymers sticking on the paver surface.

Do not apply if the paver joints are damp or wet. This will prevent the SUPERSAND G2 from properly sliding into the joints and obtaining very densely packed joints, which is critical to the product’s performance.

Temperature must be above 32°F (0°C) in dry conditions and no rain for at least 15 minutes after water activation.

For all paver surfaces, and particularly around in-ground pools, there must be a minimum slope of 1/8 inch (3 mm) per linear foot away from the edge of the pool or structures to ensure optimal performance of the SUPERSAND G2.

For the pool coping units, it is mandatory to use mortar in the joints. For the rest of the paver installation around the pool, you can use SUPERSAND G2.

Do not sweep SUPERSAND G2 over asphalt.

SUPERSAND G2 level, must be at least 1/8 inch (3 mm) below top of paver’s surface or 1/8 inch (3 mm) below the chamfer or erosion may occur. The filled and cured polymeric sand joints should never be in direct contact with foot traffic or tire.

For textured or pre-finished surfaces, we recommend to remove all the sand from the paver or slab surface prior to using the plate or roller compactor.

PLEASE NOTE:

All pavers must be completely interlocked for vehicular and pedestrian use. If pavers are fanned they are not considered interlocked. SUPERSAND G2 can be applied when pavers are installed directly on open graded aggregates that lock or choke themselves. This means the polymeric sand will not migrate through the voids. Do not apply SUPERSAND G2 when the pavers are installed directly on aggregates with large voids.